Company

Employment

Contact

Hot Products

Sale Items

Repairs

Services

Tech Info

Returns

Used Gear

Warranty

Credit

Patton Electronics 1001
Telco Rack System

High Density Rack System for Universal Access

Model 1001 Telco Rack System
High Density Rack System for Universal Access
The Model 1001 Rack System supports a variety of last-mile devices in a 2U-high, 19-inch wide rack-mount chassis with redundant AC/DC power supplies.
 
Model 1001R16
 
  Features & Benefits
  • High-density rack system supports up to 16 modems in a 2U-high, 19-inch wide rack-mount chassis with integral AC/DC power supply
  • Configurable input/output modules support all serial, voice/fax, Ethernet and G.703 DTE interfaces.
  • The NetLink rack system can expand to 320 modems in a standard 40U-high rack system.
  • Integrated SNMP and HTTP management system
  • Automatic load-sharing, dual-redundant AC and DC power supplies
  • Network management via SNMP or HTTP
  • Dual-redundant AC and DC power supplies
  • Great Modularity & Interface Functionality
 
Overview  

 

When users require higher density solutions, a rack system becomes more economical. The NetLink Model 1001 rack system consists of a 2U-high chassis that can be mounted in any standard 19-inch wide telco rack. The Model 1001 chassis supports up to 16 modem modules and a single AC or DC power supply, or dual-redundant AC or DC power supplies.

The rack shown above is a fully-configured NetLink Model 1001 rack system containing 13 modems, a network management module, and two power supply modules that fill the 18 front rack slots. Equipment/network interface modules that fill the rear slots of the rack chassis connect to the front modules through a midplane bus that extends the width of the rack.

Nearly all of the electrical and physical interfaces, from Ethernet to V.35, are available as I/O modules. Dual redundant AC or DC power supplies can be installed in the rack system to help avoid catastrophic failures caused by power fluctuations or outages.

The NetLink rack system enables users to configure, control, and perform diagnostics via SNMP or HTTP. To manage a rack system, the operator need only install a NetLink Management Module (Model 1001MC), connect a workstation to its Ethernet port, and launch a standard Web browser (i.e., Netscape Navigator or Internet Explorer). Now, any operator can manage any NetLink rack card or standalone modems from a local PC or via the Internet.


 

The Model 1001 rack system can have one or two 90, 264, VAC or -12/-24/-48 VDC power supplies installed in any combination. Each power supply can support a fully-loaded rack configured with any combination of front modem modules and rear I/O cards. If two power supplies are installed, they automatically self-configure for dual-redundant, load-sharing operation. In dual-redundant configuration, each power supply shares 50% of the load.

In the unlikely event of a supply failure, the other supply immediately begins providing 100% of required power; the operator is notified by an audible alarm; an LED flashes on the front panel; and the central site operator is notified via the network management system.

The NetLink rack systemís midplane bus connects front modem modules and rear I/O modules, delivering the right combination of modem technology and interface support. Physical/electrical interface conversion is also built-in to the system architecture. For example rack cards with G.703/G.704 interfaces will connect to V.35/X.21/EN standalone units.


 
Ordering Information
1001R16P/48V
 
16-slot Model 1001 rack; one -48VDC power supply & rear power entry module (RPEM)
1001R16P/UIK

 
16-slot 1001 rack; one 90 260VAC power supply & RPEM with an IEC-320 connector
1001R14P/R48V

 
14-slot 1001 rack; two -48VDC power supplies operating in a load-sharing, dual-redundant mode
1001R14P/RUIK 14-slot 1001 rack; two 90 260VAC power supplies & RPEMs operating in a load-sharing, dual-redundant mode
1001R14P/RUI48K
 
14-slot 1001 rack; one -48VDC & one 90 260VAC power supply, one AC and one DC RPEM operating in a load-sharing, dual-redundant mode
1001R16
 
16-slot 1001 rack with midplane bus
1001RPSM-RUI
 
90-264VAC power supply
1001RPEM-RAC
 
Rear power entry module (RPEM) with IEC-320 connector
1001RPSM-R48V
 
-48VDC power supply
1001RPEM-RVD
 
Rear power entry module (RPEM) for DC power source
1001MC
 
SNMP/HTTP management module (requires one slot)
1001CC Control module for daisy-chaining additional racks

Patton Electronics Products

 

     

1-301-924-7400
Sales Ext 17   Support Ext 25

© 2018 Data Connect Enterprise
3405
Olandwood Court
Olney, Maryland 20832